How to Make a Tri Fold Duct Tape Wallet Best Guide
Making a wallet out of everyday home items is rather intriguing. It will help you to develop new and inventive skills. Today, we’ll go through How to Make a Tri Fold Duct Tape Wallet? This wallet will feature a massive billfold, a place for an ID card, three parallel pockets, and two vertical pockets. Additionally, there will be a concealed go into the pocket of this wallet. Therefore, let us walk you through the whole process of creating this great wallet.
Materials Required
To create the wallets, you need the following materials:
- Duct Tape
- Scissors
- A Scale
- A pocket knife
- A cutting board is a large piece of thick cardboard for cutting
- For sizing, a bank card or a credit card is required.
How to Make a Tri Fold Duct Tape Wallet?
You can build several crafts using duct tape; today, I’ll demonstrate How to Make a Tri Fold Duct Tape Wallet? Duct tape is available in silver and may be purchased at WalMart, and home supply stores. Additionally, there is something termed Duck Tape; it’s a kind of tape available in vibrant colors at creative supply stores. It would help if you utilized a mix of duct tape plus Duck tape for your sticky tape wallet. It would be an excellent Father’s Day present! Follow the procedure below:
1. Measure and Cut the First Strip of Duct Tape
- To begin, measure the first strip using a scale. You don’t want the wallet to be precisely such size since this will result in a constricted fit along the length of the wallet.
- Additionally, you want some margin for mistakes to reduce afterward. Given this, 9 inches is an excellent starting point. Directly measure it out with a ruler and cut it with scissors. Then, the sticky side upset it on a level surface.
2. Constructing the Billfold
- Next, stack one piece of tape on top of another, adhesive side to silicone adhesive, leaving 1/4 inch of sticky side exposed. Then flip it over and place another strip of tape, sticky to sticky, on top of just that quarter of an inch area. Then flip over and place another piece on top of the adhesive residue left on the previous strip of tape.
- Continue in the same manner until you are out of pieces. It would help if you trimmed the edges.
3. Finishing The Billfold
- Fold the whole sheets in half and cut a 9-inch vertical strip of the other color.
- Half of your other color should be mounted on the surface of the backside of the unfolded side.
- Then split it in half lengthwise with the remaining half. Place one half on one side of the sheet, followed by the other half.
- Turn it over and collapse all of them. Then cut another nine-inch strip of the alternate color, fold it in half, and adhere it to the front edge/border. Keep the remaining half; you’ll need it later. It would help if you folded over it. Remove any extra tape.
Read Also: How to Clean Leather Wallet Easy Guide
4. Developing Pockets
Create Unique Duct Tape Strips Without Sticky Edges
- Two strands of duct tape about the diameter of your wallet folded one-piece, sticky side up, on your work surface. Place the remaining sheet on top, adhesive side down, leaving about 0.25 inches (0.64 cm) of overhang.
- You’re using much the same procedure you used with the main section of a wallet, except that you’re not allowing as much of the second strip to hang over the side.
Peel the Duct Tape Up and Wrap the Sticky Sides Down
- Remove the tape from the surface. Each side should have a large, sticky overhang. Fold them over the remainder of the duct tape to create a single strip without any sticky edges.
- You will then have a strip without sticky edges that are tiny enough to fit on one of your wallet’s inner sides.
- Create a separate strip for every pocket you choose. These pockets will be used to store cards.
1 Pockets Should Be Taped in Place
- Wallets should be opened and laid flat, with the inside facing up. On one side, start your first compartment 0.25 inches (0.63 cm) from the top of the wallet. Cut strips of duct tape exactly broad and long enough to tape the pocket’s sides and bottom to the wallet.
- The tape strips used to secure the pocket should be approximately 0.30 inches (0.64 cm) broad and long enough to cover the whole edge on every side, excluding the top.
- Maintain a safe distance between the tape strips and the central crease since the crease may cause the pieces to pull up with time.
Subsequent Pockets Should Be Layered Beneath the First
- Place the other pocket in front of the first, about 0.25 inches (0.64 cm) from the first pocket’s top border. Tape tiny pieces of duct tape to the pocket’s sides and bottom, leaving the top uncovered.
- Trim your pocket as you go if necessary to ensure they are all the identical size.
- Continue downward until you approach the wallet’s bottom. The last pocket must be around 0.25 inches (0.64 cm) first from the bottom to allow for tape placement.
Add Pockets to the Opposite Side

- If desired, you can attach pockets on the other edge inside. Create strips of sticky tape in the same manner and tape them in layers. If, on the other hand, you want a spacious pocket with an ID card holder, avoid placing card pockets on the other side.
- Alternatively, you may create a more oversized pocket by including an ID holder.
5. Construct a Single Huge Credit Card Pocket
- Tear two 5-inch strips in half and stack them. Then, using the same process as for the main section of the wallet, adhere two additional 5-inch pieces to the rear and overlap over the sides.
- Trim the borders of the pocket with the knife blade and ruler to make it 4 inches wide.
6. Organize the Pockets
- Arrange the three pockets vertically, with the giant pocket at the bottom. The center pocket will not extend to the bottom, which is OK.
- Attach them with a ripped lengthwise strip of tape.
Read Also: How to Match Handbag With Outfit Suitable Guide
7. Construct the wallet
- Arrange your primary fabric with the UP side towards The front of the wallet.
- Attach the credit or debit card compartments to the top right using a 9-inch longitudinal duct tape strip.
- Then fold the purse in half and bind the ends with torn-in-half lengthwise strands of tape. Remove any excess.
FAQs – How to Make a Tri Fold Duct Tape Wallet?
Is Duct Tape Adhesive to Plastic?
Yes, but only under limited circumstances. Duct tape doesn’t adhere well to plastics since the adhesive on such materials is intended for that substance, and it might be too harsh for duct tape. Duct tape is self-adhesive tape that adheres to a range of different surfaces. Although it is generally used for minor repairs, you may use it to secure ductwork joints.
Can Duct Tape Be Used to Eliminate Warts?
Proceed with your day by applying a little strip of duct tape straight to the wart’s region. Loosen the duct tape every 3 to 6 days and massage the wart, including an emery cloth or pumice stone. Additionally, you may choose to soak the wart in hot water while it is exposed.
Is Duct Tape Made of Metal?
The “original” duct tape is self-adhesive aluminum foil; the metal side transmits, and metal should. If the material is entirely plastic, it is relatively non-conductive. However, this also relies on your interpretation of the term “conductor.”
Conclusion
Finally, we hope that you find the procedure for How to Make a Tri Fold Duct Tape Wallet? detailed here beneficial. Individuals interested in do-it-yourself components can make the most effective use of this technique. When using an Exacto knife, you should ensure that your hand is adequately secured. We appreciate your time. Have a lovely day!
Read More